Model A Ford Club of Great Britain
Model A Ford Club of Great Britain

Please Note: These are generally the original

specs and relate to the 3.3 litre  engine.

 

CRANKSHAFT
 

Weight 28 lbs
Main Bearings: 1.624" Dia
Crank Pins: 1.499" Dia
Crank Pin Taper and Roundness: .0005" 
to .001"

Rear Flange Thickness: 3/8"
End Clearance: .004" to 007"
Main Bearing Clearance: .001"
Crankshaft Straightness: .0005"
Main Bearing Car Torque:80-100lbs

 

CONNECTING RODS
 

Weight:1lb, 6oz
Balance Weight:552 gms +/-1 gmm,
 crank end

198 gmms +/- 1 gmm, pin end
Crankshaft Bearing:1-1/2" Dia.
Piston Pin Bearing:1" Dia.
Bearing Side Clearance:.008" to .012"
Piston Pin Clearance:.0005"
Crankshaft Clearance:.001"
Bearing Cap Bolt torque:40 - 50 lbs
Assembled with Oil Dippers Facing 
Camshaft

 

IGNITION
 

Rotor Rotation:counter clockwise
Point Gap:.016" to .020"
Condenser Capacity:.20 to .25 MFD
Spark Plug:Champion 3X, 7/8-18 Thread
Spark Plug Gap:.035"
Spark Manual Advance:20 Deg
Rotor Air Gap:.025"

 

VALVES
 

Lift:.287" with .015" Clearance
Seat Angle:45 Deg
Seat Width:3/32"
Stem Dia:.311"
Valve Length:5.677"
Head Diameter:1.537"
Valve Opening Dia:1-3/8"
Port Dia:1-3/8"
Valve Clearance:Exhaust .002":Intake .001" 
to .0015"

Lifter Clearance:Exhaust .015"
Intake .013"
Valve Guides:ID .3135":OD. .5938"
Valve Spring:OD 1.022":Valve
Timing

Intake opens 7-1/2 deg BTDC
 Intake Closes 48-1/2 deg A BDC
Exhaust Opens 51-1/2 deg Before BDC
Exhaust Closes 401/2 ATDC

 

TRANSMISSION
                   

Gear Ratio:High 1;1 Second 6.9:1,

Low 8.75:1
Bearings:Main Shaft Front Ball--1208
Main Shaft Rear Ball--1306
Counter Shaft Short --Bower J241256
Counter Shaft Long--Bower J241246
Pilot Bearing--SKF 2RSJ

 

DRIVESHAFT


Spline Inner Dia: .901" to .911"
Spline Outer Dia: 1.090" to 1.091"
Pinion Bearing Torque: 15 to 20 inch lbs

 

LUBRICATION
 

Oil Pump Type:Gear
Pump capacity:9 Pints/min @ 1300 RPM
Pump Gear Teeth To Housing Clearance:.001" 
to .002"

Cover To Gear Face Clearance:.001" to .002"
Drive Gear to Camshaft Gear Clearance:.003" 
to .005"

 

GAS TANK
 

Capacity:1928/29, 10 US Galls: 1930/31, 11 US Gall

 

SPRINGS
 

Front - Free Length:(10 Leaf) 30-5/8" to 30-13/16"

Rear - Free length:Tudor/Fordor 38-7/8" to 39"

Phaeton, Roadster, Coupe 39-1/8" to 39-1/2"

 

CLUTCH
 

Pressure Plate Weight:15  lbs
Clutch Disc Weight:2-1/2" lbs
Clutch Pressure:1100 lbs
Foot Pedal Pressure:30 lbs.
Clutch Dia:9", Thickness:9/64"
Clutch pedal Clearance ( Free Play ):1".
Clutch Release Bearing:Bower 2065

 

CYLINDER BLOCK

 

Cylinder    Bore: 3.875" to 3.876"
Valve Guide Bore: .594" to .595"
Flatness On Top block: .003"
Cylinder Bore Perpendicular to Top: .001" to .002"

 

FLYWHEEL

 

Weight:63lbs, 4oz.
Balance Within .15 In/oz
Flywheel Bolt Torque:65 Ft/lbs
Clutch Mounting surface and disc surface
must run true to crankshaft within .005" TIR.
Clutch mounting shoulder diameter must be
concentric with crankshaft flange diameter within

.005" TIR

Pilot bearing GMN6203DV

 

COOLING SYSTEM


Water Pump Shaft:5/8" Dia
Water Pump Shaft end Play:.006 to .010"
Radiator Hoses:1928/29 - upper 2" Dia., 6-1/4" Long
1930-31 - upper 2" Dia., 8" Long
Lower ( two pieces ) 1-3/4" Dia, 2-3/4" Long
System Capacity:3 Galls
Radiator Capacity:1-1/2 US Galls.
Radiator Flow 38  US GPM

 

CAMSHAFT
 

Shaft  Dia:7/8"

Bearing Dia:1.560"
Block Bore Dia:1.561"
Bearing Clearance (MAX):.003"
Cam Lift:.303"
Duration:236 Deg
Timing gear Cover Spring: Tension 35 lbs.
Timing Gear Backlash:.003 to .005" (max .009)
Camshaft Straightness:.0005" to .001"

 

RADIATOR

 

Tubes:1928 Round, 1/4 Dia
Number of Tubes:94 in 4 rows
1929 Round, 1/4 Dia
Number of Tubes:100 in 4 rows, or 87 in 5 rows
Tubes 1930/31 Flat, 5/32 x 1/2"
Number of Tubes:102 in 3 rows
Flow Rate:38  US GPM

 

ENGINE

 

Rated Horse Power: 24.03  SAE ( US)
Brake Horse Power: 40 HP (US)

Firing order 1-2-4-3
Compression Ratio:4.22:1
Piston Displacement:200.5 Cu. In. ( 3283cc)
Bore:3.876"
Stroke:4.250"

 

CYLINDER HEAD


Compression ratio :   1928:4.3:1        1929/31:4.22:1

 

PISTONS
 

Displacement:200.5 cu. Inches
Weight:1 lb. 1-7/8 oz (476.8 gms)
Variance in weight:+/- gms
Diameter:3.8745" (Bore 3.875)
Variation in Piston Compression Height:.003" to .005"
Piston Pin Bushing:ID .992", to OD. 1.0675"
Pin Fit In Rod Bushing:.0003" MAX
Pin fit In Piston:.0002", to .0005"
Piston Fit In Cylinder:, .002"
Ring Clearance in Grove:.001" to .002"
Ring End Gap:TOP- .012":to .015"
Middle- .010 to .012":Bottom-   .008 to .010"

 

STEERING

 

Turning Radius:17 Ft.
Gear Ratio:1928/29 11-1/4:1:1930/31 13;1
Steering Wheel Dia:1928/29 17-1/2":1930/31 17"
Sector Shaft Bearing Clearance:.001" to .0015"
Bearings:7 Tooth T83:2- Tooth Timken 3571

 

  
Print Print | Sitemap
© MAFCGB